The GAS-727 Clean Boost Pedal - Two GAS-707 Clean Boost in one case!
Special features:
* Two totally independent GAS-707 units in one pedal
*Added switch for +20dB output level on the second GAS-707
*Added 'Bolt/Serial'-switch for two different working modes
*Added 'GO!' switch for momentary
switching mode of the second GAS
*Illuminated rocker switches when switched to 'ON'
*Specially dimensioned and selected components = overdrive at its best!
*True Bypass with less switching noise
*'Long-Life'-foot switch
*Two 'Bass-Boost'-switches
*Upside blending of lasered high-grade steel
*Extremely bright green and blue Jewel-LEDs
*Power supply by external AC/DC-adapter
*Handmade in small series
*2 years warranty
Special features:
Looking inside the GAS-727 you will find two totally seperated GAS-707
Clean Boost in the same case, connected serial. Both GAS-707 have their
own Tone- and Level controls on the top panel and seperated Bass-Boost switches on the front panel.
The second in line can be switched over into a +20dB Mode which features more output level. Besides that the GAS-727 has been given an extra switch for Bolt or Serial using mode. Also new is the GO! Rocker Switch for Momentary Using Mode.
Finally the new GAS-727 includes a True Bypass switching system, with less switching noise!
GO! Rocker Switch: (Front Panel)
When switched to 'ON' the GAS-727 (blue) runs in GO! Mode.
The GO! Rocker Switch activates the 707 (blue) to momentary mode.
The GAS-707 (blue) is activated by stepping on the footswitch and keeping it pressed, and returns to the previous setting by letting go again.
The GO! Mode changes the second footswitch (GAS-707 blue) to a Momentary Switch for single notes or little Fill Ins - only active when
stepped on!
In Serial Mode the GAS-707 (blue) is switched in series to the actual setting, in Bolt Mode it will switch off the previous sound setting and activate the GAS-707 (blue).
Bolt Rocker Switch: (Front Panel)
When switched to 'ON' the pedal runs in Bolt Mode.
Bolt-Mode:
Each GAS can be activated by pushing the usual On-Off switch on the pedal top but only one of them can be used when put on Bolt Mode.
The Advantage: Switching from GAS 1 to GAS 2 is only one footstep away, without having to disactivate GAS 1. It shuts off automatically. Same way around when going from GAS 2 to GAS 1.
Serial-Mode:
Both GAS can be run at once without getting across each other. This way both GAS can be run Serial.
Sound:
Please look at the GAS-707 and GAS-808!
Bass Boost Switches:
(Front Panel)
When switched to 'ON' the pedal runs in Bass Boost Mode.
Both GAS pedals have their own Bass Boost Switch to push the lower frequencies. The switch for the first 707 (green) is located on the right side,
the switch for the second 707 (blue) is located on the left side.
+20dB Rocker Switch: (Front Panel)
When switched to 'ON' the GAS-707 (blue) runs in +20dB output level mode.
This offers 5x more output level than the standard GAS-707.
Jacks:
You will find the Input Jack righthandside and the Output Jack lefthandside the GAS-727.
External power supply:
On the rear of the pedal you can find the Jack for an external power supply. Its a standard jack (2,1mm). You can use the usual adapters for floor effects (9V DC,+ = outside ring, ground = inside).
The GAS-727 can be driven only with an external power supply - not with battery.
Please use a high quality power supply - stabilized only!
Technical Data:
*Input Level: -20dB
*Input Impedance: 1MOhm
*Output Impedance: 100 KOhm
*Dimensions (L/T/H (inch)):
4.7 x 3.7 x 1.3
*Weight: 1.1 lbs
*Power Supply: AC/DC adapter use 9V DC stabilisized only.
*Polarity: + = outside ring, ground = inside
Handmade in small series each GAS pedal is unique!
